- Pizza Stone for Solymac Oven
- Pizza stone for oven BAKERS PRIDE
- Pizza stone for BARTSCHER oven
- Pizza stone for Cookmax oven
- Refractory stone for CUPPONE pizza oven
- Pizza stone for FIMAR oven
- Pizza stone for GAM oven
- Pizza stone for oven GGF
- Refractory Stone for Italforni Pizza Oven
- Pizza stone for Moretti oven
- Refractory Stone for OEM Pizza Oven
- Pizzagroup Refractory Stone
- Refractory Stone for Prismafood Pizza Oven
- Pizza stone for oven RESTO ITALIA
- Pizza stone for Tornati oven
- Pizza stone for ZANOLLI oven
- Pizza stone for ZANUSSI oven
- Refractory stone for gas oven
- Refractory stone for pizza oven FORNITALIA
- Refractory stone for Rinaldi Superforni pizza oven
- Refractory stone for electric oven
- Matricola ML 44 Refractory Stone for Oven
- Round Refractory Stone for Pizza Oven
OEM SG 99 Gas Cylinder Nozzle Kit – G30
The OEM SG 99 gas cylinder nozzle kit is designed for the maintenance and repair of compatible OEM SG 99 professional gas pizza ovens.
This kit is intended for the G30 gas cylinder configuration operating at 28–30 mbar, provided that these specifications match the oven’s approved setup.
It contains 8 gas jets and injectors for the central deck burner, left and right upper burners, ignition pilot and intermediate flame-transfer burner.
Each injector controls the gas flow to a specific burner. Therefore, the correct orifice size and installation position are essential.
Before ordering, always check the oven identification plate and compare the kit with the original gas injectors.
Complete 8-Piece OEM SG 99 Nozzle Kit
The kit includes the following components:
- 4 × Ø0.95 mm gas jets for the central deck burner.
- 2 × Ø1.15 mm gas jets for the left and right upper burners.
- 1 × Ø0.22 mm pilot jet for the small ignition pilot burner.
- 1 × Ø0.70 mm injector for the intermediate flame-transfer burner.
Total: 8 gas jets and injectors in four different orifice sizes.
Each component is intended for a specific part of the oven’s combustion or ignition system.
For this reason, the injectors must not be interchanged between burners.
Their dimensions, threads and mounting positions must also match the manufacturer’s specifications.
4 × Ø0.95 mm Jets for the Central Deck Burner
The kit contains four Ø0.95 mm gas jets for the central deck burner.
The deck forms the lower part of the pizza baking chamber.
Its heating system contributes to cooking the pizza base and dough.
The gas jets regulate the amount of gas supplied to the burner.
As a result, their orifice size must correspond to the oven’s approved gas configuration.
Before installation, the technician must confirm the correct burner positions and injector specifications.
2 × Ø1.15 mm Jets for the Left and Right Upper Burners
The kit also contains two Ø1.15 mm gas jets.
These are intended for the upper burner system:
- 1 jet for the right-hand upper burner.
- 1 jet for the left-hand upper burner.
The upper burners contribute to heating the top section of the baking chamber.
They therefore play a role in cooking the pizza toppings and upper surface.
However, their injector sizes differ from those used for the central deck burner.
Consequently, the two types must not be mixed up during installation.
1 × Ø0.22 mm Jet for the Ignition Pilot Burner
The kit includes one Ø0.22 mm pilot jet.
This injector is intended for the small ignition pilot burner.
Its purpose is to meter the gas supplied to the pilot flame, according to the oven’s original design.
The pilot burner forms part of the ignition system on ovens equipped with this arrangement.
However, a pilot flame problem is not always caused by a blocked or damaged injector.
It may also involve the ignition electrode, thermocouple or another part of the gas system.
Therefore, a qualified technician should diagnose the fault before replacing the pilot jet.
1 × Ø0.70 mm Jet for the Intermediate Flame-Transfer Burner
The kit also includes one Ø0.70 mm gas jet.
This component is intended for the intermediate flame-transfer burner.
Depending on the oven’s design, this burner helps transfer ignition between designated areas of the system.
The injector meters the gas supplied to this intermediate burner.
As with the other jets, its size and position must match the original installation.
It must not be replaced with an injector intended for the deck or upper burners.
G30 Gas Cylinder Version – 28–30 mbar
This OEM SG 99 nozzle kit is intended for an oven configuration using G30 gas at 28–30 mbar.
Before ordering, check the information on the oven’s identification plate.
Different gas types and operating pressures may require different injector sizes and equipment.
Therefore, nozzles intended for a G30 gas cylinder setup must not be confused with those designed for G20 natural gas.
Compatibility with G31 propane must also be verified separately. It should not be assumed from the G30 designation alone.
Why Are Different Gas Jet Sizes Required?
The OEM SG 99 oven uses several burners with different functions.
The central deck burner heats the lower baking area.
The upper burners provide heat to the upper section of the oven.
The pilot burner contributes to the ignition system.
Finally, the intermediate flame-transfer burner performs its designated ignition-transfer function.
Each part of the system requires gas delivery appropriate to its design.
This is why the kit contains four different injector sizes:
- Ø0.95 mm;
- Ø1.15 mm;
- Ø0.22 mm;
- Ø0.70 mm.
A qualified technician must respect the specified injector positions.
When Should Pizza Oven Gas Jets Be Replaced?
Over time, gas injectors may become obstructed or damaged.
In some cases, this can interfere with normal burner operation.
However, abnormal combustion does not necessarily mean that the injectors are defective.
The issue may also involve gas pressure, the burner itself or another component of the installation.
For this reason, a qualified technician should identify the cause before carrying out a replacement.
Injector inspection and replacement should follow the oven manufacturer’s maintenance instructions.
G30 Gas Cylinder Kit or G20 Natural Gas Kit?
The kit on this page is intended for the G30 gas cylinder version of the OEM SG 99 pizza oven.
It is not the same as the kit designed for G20 natural gas, also known as mains gas.
If your oven uses G20, see our OEM SG 99 Natural Gas G20 Nozzle Kit.
Before purchasing either kit, confirm the oven’s gas category and approved operating configuration.
Replacing gas injectors alone does not constitute a complete gas conversion procedure.
Any change of gas type must be permitted by the oven manufacturer and carried out by a qualified professional.
How to Check Compatibility Before Ordering
Before ordering, check the oven identification plate and the original injector specifications.
Pay particular attention to:
- Oven manufacturer: OEM.
- Oven model: SG 99.
- Gas type: G30.
- Operating pressure: 28–30 mbar.
- Central deck burner: 4 × Ø0.95 mm jets.
- Left and right upper burners: 2 × Ø1.15 mm jets.
- Ignition pilot burner: 1 × Ø0.22 mm jet.
- Intermediate flame-transfer burner: 1 × Ø0.70 mm jet.
Also verify the threads, physical dimensions and mounting arrangements of the original parts.
If you are unsure, contact ACRIVI with the oven’s identification details before placing your order.
Spare Parts for Professional Pizza Oven Maintenance
Professional gas pizza ovens require appropriate inspection and maintenance of their burner systems.
The gas injectors are among the components a technician may need to check.
When replacement is necessary, the correct nozzle sizes and positions must be maintained.
This 8-piece OEM SG 99 nozzle kit brings together injectors for different heating and ignition functions.
It is intended for compatible professional ovens used in pizzerias, restaurants and commercial kitchens.
Installation and Gas Safety
Gas injectors are part of the oven’s gas supply and combustion system.
Therefore, their replacement requires specialist technical knowledge.
Before any work begins, the gas supply must be shut off and the oven taken out of service.
The appliance must also be allowed to cool completely.
Installation, adjustment and safety checks must be performed by a qualified gas technician.
The technician must follow the manufacturer’s instructions and confirm the correct position of every injector.
Never drill, enlarge or modify an injector orifice.
Do not interchange jets between different burners.
After installation, the technician must carry out the required gas-tightness, combustion and operational checks before returning the oven to service.
OEM SG 99 G30 Nozzle Kit Specifications
- Product: gas nozzle and injector kit.
- Oven manufacturer: OEM.
- Oven model: SG 99.
- Application: professional gas pizza oven.
- Gas version: gas cylinder.
- Gas category: G30.
- Operating pressure: 28–30 mbar.
- Kit contents: 8 gas jets and injectors.
- Central deck burner: 4 × Ø0.95 mm.
- Left and right upper burners: 2 × Ø1.15 mm.
- Ignition pilot burner: 1 × Ø0.22 mm.
- Intermediate flame-transfer burner: 1 × Ø0.70 mm.
- Injector threads: to be checked against the original parts.
- Compatibility: OEM SG 99 with the corresponding approved gas configuration.
- Installation: qualified gas technician.
Buy Your OEM SG 99 Gas Nozzle Kit from ACRIVI
ACRIVI supplies spare parts for professional pizza oven maintenance and repair.
Looking for a gas cylinder nozzle kit for your OEM SG 99 pizza oven?
This kit contains injectors for the central deck burner, upper burners, ignition pilot and intermediate flame-transfer burner.
The stated composition includes 8 components with orifice sizes of Ø0.95 mm, Ø1.15 mm, Ø0.22 mm and Ø0.70 mm.
Before ordering, compare the supplied kit specifications with your oven’s original configuration.
If you need assistance, contact ACRIVI with your oven model and identification plate details.
Always use correctly matched gas injectors and have installation and safety checks performed by a qualified professional.
